Aquatics Blog

Cast-in-Place vs. Shotcrete Concrete Pool Installation

For many, the question commonly arises as to what type of concrete material makes the best watertight vessel: cast-in-place concrete, shotcrete or gunite. While each have their own strengths, one must consider key items such as geographical/site location, soil conditions and most importantly, availability.

There are many locations in the United States where shotcrete and gunite are not produced. Soil conditions can also play an integral role in the decision making. Questionable and/or remediated soils often call for thicker concrete placement due to the needed increase of structural steel (rebar).

The placement method utilized for concrete is to discharge it from a ready-mix truck down a shoot directly into form work or into a hopper equipped with a boom pump. The concrete is then pumped into forms and must be vibrated for compaction. By contrast, the shotcrete process, whether using wet or dry material feed, may only require single side forming or no forming at all by utilizing the earth as the back form in selected areas. This process utilizes a smaller pump with added air pressure via an accompanying compressor. The air is introduced atshotcrete the end of the discharge hose nozzle, creating a high-pressure discharge of the concrete mix. The pressure creates compaction, thereby enhancing design creativity and application flexibility, often resulting in a savings of time or money. The impact velocity of correctly placed shotcrete quickly compacts the material, yielding an “in-place” mix that’s richer in cement and higher in strength than the same mixture prior to placement. With shotcrete, what appears to be a waste of supplies, known as “rebound” or overspray, in reality ends up in thick, high-energy shotcrete as a portion of the mixture ricochets off the receiving area and away from the placement area. The loss through rebound will vary based on various factors including the dryness of the mix, the shooting distance from the surface area and wind conditions. The expected thickness is generally overshot, trimmed back to the design thickness reflected through "look-outs," and finished to the required surface consistency and appearance. This process commonly requires more labor for multiple finishers to cut and finish the concrete and laborers to follow with clean-up and rebound removal. Compared to the additional materials and labor required to form both sides for the cast-in-place process, this can often times offset each other. However, cast-in-place does require additional labor for front and back form removal.

Characteristics of how concrete or shotcrete is delivered for pumping or placements are very similar. Typically, regardless of the concrete type, shotcrete or cast-in-place concrete has a 90-minute window from the time it is batched at the plant until it placed. Temperature of the material, air temperature and humidity levels can increase or decrease the set times of the concrete. Typically, ready-mix companies hold back 10-15 gallons of water in the mix so the contractor can adjust the slump of the concrete onsite. A concrete truck typically hauls 8 to 10 yards of concrete and 1 cubic yard of concrete typically contains 38 to 40 gallons of water. Project specifications dictate the required mix design and testing agencies commonly verify the concrete slump of the first truck prior to pumping, as well as periodically through the day. Adding 1 gallon of water over the design mix (amount of gallons of water per yard of concrete) can decrease the strength of the concrete by 200 PSI.

Often overlooked, the curing process is an integral step for optimum intended performance of concrete or shotcrete. The mix design can be perfect and the placement can be of the highest quality, but if not cured properly, adverse effects can impact the quality dramatically. While there are many methods, curing concrete or shotcrete surfaces with water is by far the best method for maintaining adequate moisture and controlling shrinkage cracks during the hydration process. After some time, the concrete starts the chemical reaction that eventually hardens the concrete. Curing vertical and horizontal surfaces with water can be easily accomplished with alternative curing methods considered due to project scheduling, the availability of fresh water and the ability to discharge the water being used. Curing compounds may also be applied to the concrete or shotcrete mix or to concrete surfaces after placement. However, these compounds can also have an adverse effect on the finish materials such as paint, plaster or tile mortar. It is suggested to consult with the finish contractor and the structural engineer prior to concrete placement to verify acceptance of curing compounds.

In closing, the question of which process is better? Well, as you can see, there are many variables to consider. While cast-in-place is better-controlled and suited for close tolerance work, it can be a less economical option. Shotcrete, if applied properly, can also provide a superior watertight vessel. Counsilman-Hunsaker's advice? Make sure your concrete or shotcrete contractor is qualified to perform their work. Do your research. Ask for references and verify if their nozzleman is American Shotcrete Association-certified. Water test your pool prior to the placement of pool finishes. This process is detailed in American Concrete Institute 350.

Remember that pool finishes, such as paint, plaster and/or tile, are not designed to waterproof your pool. If the structure behind your finish is not watertight, your finishes will only serve as a temporary barrier.

  • Illinois Swimming Facility Legislation in Final Stages...

    Read More
  • Strange Bedfellows: Aquatics and College Football

    Read More
  • Cloudy Water Solutions Checklist

    Read More

Illinois Swimming Facility Legislation in Final Stages...

Read More

Strange Bedfellows: Aquatics and College Football

Read More

Cloudy Water Solutions Checklist

Read More